Q1:
AS & A Level Physics - 9702 Paper 2 2011 Summer Zone 1
Share
Previous
Questions:
1/7
Topic: CH2 - MEASUREMENT TECHNIQUES
Solution
PRACTISE
Similar Questions
LEARN
Concepts with Sparky
More Questions from this Topic
Theory
CH2 - MEASUREMENT TECHNIQUES
(a) The list below shows some SI quantities.
Underline the quantity that is not an SI base quantity.
charge current length time [1]
(b) A square so...
Summer
6
Theory
CH2 - MEASUREMENT TECHNIQUES
The drag force $F_D$ acting on an object falling through air is given by
$F_D = \frac{1}{2}C \rho A v^2$
where $A$ is the cross-sectional area of th...
Summer
5
Theory
CH2 - MEASUREMENT TECHNIQUES
The drag force $F_D$ acting on a sphere falling through a liquid is given by
$$F_D = 6 \pi \eta r v$$
where $r$ is the radius of the sphere,
$v$ is...
Summer
6
Theory
CH2 - MEASUREMENT TECHNIQUES
(a) Define density. [1]
(b) Figure 1 shows a cuboidal glass block.
A student measures the mass $m$ of the block and the side lengths $...
Winter
5
MCQ
CH2 - MEASUREMENT TECHNIQUES
The value of quantity $X$ has a percentage uncertainty of 2%.The value of quantity $Y$ has a percentage uncertainty of 4%.The value of a quantity $W$ ...
Summer
6
MCQ
CH2 - MEASUREMENT TECHNIQUES
What is a reasonable estimate of the mass of a solid sphere of copper that has a diameter of 60 cm?
Winter
5
MCQ
CH2 - MEASUREMENT TECHNIQUES
A solid bar has a square cross-section. Its length is measured as 50.0 ± 0.2 cm and its width is measured as 2.00 ± 0.01 cm.These values are used to...
Winter
4
MCQ
CH2 - MEASUREMENT TECHNIQUES
The density of the material of a rectangular block is determined by measuring the mass and linear dimensions of the block. The list shows the results ...
Winter
3
MCQ
CH2 - MEASUREMENT TECHNIQUES
What is a reasonable estimate of the volume of one page from this examination paper?
Winter
4
MCQ
CH2 - MEASUREMENT TECHNIQUES
A thermometer can be read to an accuracy of ±0.5°C. This thermometer is used to measure a temperature rise from 40°C to 100°C. What is the percent...
Summer
4
More Questions from year 2011
Theory
CH2 - MEASUREMENT TECHNIQUES
Measurements made for a sample of metal wire are shown in Fig. 1.1.
Fig. 1.1
(a) State the appropriate instruments used to make each of these meas...
Summer
2
Theory
Kinetic Energy
(a) Explain what is meant by work done. [1]
(b) A car is travelling along a road that has a uniform downhill gradient, as shown in Fig. 2.1.
...
Summer
3
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) Explain what is meant by centre of gravity.
(b) Define moment of a force.
(c) A student is being weighed. The student, of weight $W$, stands 0.3...
Summer
3
Theory
CH9 - DEFORMATION OF SOLIDS
(a) Define, for a wire,
(i) stress, [1]
(ii) strain. [1]
(b) A wire of length 1.70 m hangs vertically from a fixed point,...
Summer
3
Theory
CH20 - D.C. CIRCUITS
(a) A variable resistor is used to control the current in a circuit, as shown in Fig. 5.1. The variable resistor is connected in series with a 12V po...
Summer
1
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) State two assumptions of the simple kinetic model of a gas. [2]
(b) Use the kinetic model of gases and Newton's laws of motion to exp...
Summer
3
Theory
CH15 - SUPERPOSITION
(a) Explain the term interference. [1]
(b) A ripple tank is used to demonstrate interference between water waves.
Describe
(i) the appa...
Summer
2
Theory
CH1 - PHYSICAL QUANTITIES & UNITS
(a) Distinguish between scalar quantities and vector quantities. [2]
(b) In the following list, underline all the scalar quantities.
accelerati...
Summer
4
Theory
CH1 - PHYSICAL QUANTITIES & UNITS
(a) A sphere of radius $R$ is moving through a fluid with constant speed $v$. There is a frictional force $F$ acting on the sphere, which is given by ...
Summer
2
Theory
Potential Energy
(a) (i) Explain what is meant by work done. [1]
(ii) Define power. [1]
(b) Fig. 3.1 shows part of a fairground ride with a carriage on rai...
Summer
2