Q17:
AS & A Level Physics - 9702 Paper 1 2011 Winter Zone 2
Share
Previous
Questions:
17/40
Topic: Efficiency and Energy Density
Solution
Solution is B,A,A
PRACTISE
Similar Questions
LEARN
Concepts with Sparky
More Questions from this Topic
MCQ
Efficiency and Energy Density
A constant force $F$, acting on a car of mass $m$, moves the car up the slope through a distance $s$ at constant velocity $v$.
The angle of the slope...
Summer
3
MCQ
Efficiency and Energy Density
A constant force $F$, acting on a car of mass $m$, moves the car up the slope through a distance $s$ at constant velocity $v$. The angle of the slope ...
Summer
2
MCQ
Efficiency and Energy Density
In many old-style filament lamps, as much as 92 J of energy is emitted as thermal energy for every 8 J of energy emitted as light.
What is the effici...
Winter
3
MCQ
Efficiency and Energy Density
An electric motor is required to produce 120 W of mechanical output power. The efficiency of the motor is 80%.
Which is correct?
Winter
1
MCQ
Efficiency and Energy Density
An electric motor is required to produce 120 W of mechanical output power. The efficiency of the motor is 80%.
Which row is correct?
Winter
2
MCQ
Efficiency and Energy Density
The data below are taken from a test of a petrol engine for a motor car.
power output 150 kW
fuel consumption 20 litres per hour
energy content of ...
Summer
2
MCQ
Efficiency and Energy Density
The diagram shows the design of a water wheel which drives a generator to produce electrical energy. The flow rate of the water is 200$ kg s^{-1...
Summer
3
MCQ
Efficiency and Energy Density
The pump of a water pumping system uses 2.0 kW of electrical power when raising water. The pumping system lifts 16 kg of water per second through a ve...
Winter
2
MCQ
Efficiency and Energy Density
A bow of mass 400 g shoots an arrow of mass 120 g vertically upwards. The potential energy stored in the bow just before release is 80 J. The system h...
Summer
3
More Questions from year 2011
Theory
CH2 - MEASUREMENT TECHNIQUES
Measurements made for a sample of metal wire are shown in Fig. 1.1.
Fig. 1.1
(a) State the appropriate instruments used to make each of these meas...
Summer
2
Theory
Kinetic Energy
(a) Explain what is meant by work done. [1]
(b) A car is travelling along a road that has a uniform downhill gradient, as shown in Fig. 2.1.
...
Summer
3
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) Explain what is meant by centre of gravity.
(b) Define moment of a force.
(c) A student is being weighed. The student, of weight $W$, stands 0.3...
Summer
3
Theory
CH9 - DEFORMATION OF SOLIDS
(a) Define, for a wire,
(i) stress, [1]
(ii) strain. [1]
(b) A wire of length 1.70 m hangs vertically from a fixed point,...
Summer
3
Theory
CH20 - D.C. CIRCUITS
(a) A variable resistor is used to control the current in a circuit, as shown in Fig. 5.1. The variable resistor is connected in series with a 12V po...
Summer
1
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) State two assumptions of the simple kinetic model of a gas. [2]
(b) Use the kinetic model of gases and Newton's laws of motion to exp...
Summer
3
Theory
CH15 - SUPERPOSITION
(a) Explain the term interference. [1]
(b) A ripple tank is used to demonstrate interference between water waves.
Describe
(i) the appa...
Summer
2
Theory
CH1 - PHYSICAL QUANTITIES & UNITS
(a) Distinguish between scalar quantities and vector quantities. [2]
(b) In the following list, underline all the scalar quantities.
accelerati...
Summer
4
Theory
CH1 - PHYSICAL QUANTITIES & UNITS
(a) A sphere of radius $R$ is moving through a fluid with constant speed $v$. There is a frictional force $F$ acting on the sphere, which is given by ...
Summer
2
Theory
Potential Energy
(a) (i) Explain what is meant by work done. [1]
(ii) Define power. [1]
(b) Fig. 3.1 shows part of a fairground ride with a carriage on rai...
Summer
2