Q22:
AS & A Level Physics - 9702 Paper 1 2011 Winter Zone 2
Share
Previous
Questions:
22/40
Topic: CH9 - DEFORMATION OF SOLIDS
Solution
Solution is A,A
PRACTISE
Similar Questions
LEARN
Concepts with Sparky
More Questions from this Topic
Theory
CH9 - DEFORMATION OF SOLIDS
(a) State Hooke's law. [1]
(b) The variation of the applied force with the extension for a sample of a material is shown in Fig. 3.1.
...
Summer
10
Theory
CH9 - DEFORMATION OF SOLIDS
(a) Define strain. [1]
(b) A copper wire of length 4.0 m has a uniform cross-sectional area of $4.5 \times 10^{-7} \text{ m}^2$.
A tensi...
Summer
3
Theory
CH9 - DEFORMATION OF SOLIDS
(a) The variation of stress with strain for a metal P is shown in Figure 1.
Point E is the elastic limit of the metal.
(i) Use Figure 1 to determi...
Winter
4
Theory
CH9 - DEFORMATION OF SOLIDS
(a) Define:
(i) stress [1]
(ii) strain [1]
(b) Two wires X and Y, with equal unstretched lengths of 0.84 m, are suspended ...
Winter
8
Theory
CH9 - DEFORMATION OF SOLIDS
(a) Define the Young modulus of a material. [1]
(b) A metal wire P that obeys Hooke’s law is stretched within its limit of proport...
Winter
5
MCQ
CH9 - DEFORMATION OF SOLIDS
A sample of metal is subjected to a force which increases to a maximum value and then decreases back to zero. A force–extension graph for the sa...
Summer
4
MCQ
CH9 - DEFORMATION OF SOLIDS
Two wires, P and Q, made of the same material, are stretched with an increasing force.
A graph is plotted of the variation with force of the extensio...
Summer
5
MCQ
CH9 - DEFORMATION OF SOLIDS
An extension–force graph for a spring is shown.
What is the spring constant of the spring?
Summer
3
MCQ
CH9 - DEFORMATION OF SOLIDS
What is a unit for stress?
Winter
6
MCQ
CH9 - DEFORMATION OF SOLIDS
A wire has original length $L$ and cross-sectional area $A$. A tensile force $F$ is applied to the wire which causes it to have extension $x$. The wir...
Winter
4
More Questions from year 2011
Theory
CH2 - MEASUREMENT TECHNIQUES
Measurements made for a sample of metal wire are shown in Fig. 1.1.
Fig. 1.1
(a) State the appropriate instruments used to make each of these meas...
Summer
2
Theory
Kinetic Energy
(a) Explain what is meant by work done. [1]
(b) A car is travelling along a road that has a uniform downhill gradient, as shown in Fig. 2.1.
...
Summer
3
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) Explain what is meant by centre of gravity.
(b) Define moment of a force.
(c) A student is being weighed. The student, of weight $W$, stands 0.3...
Summer
3
Theory
CH9 - DEFORMATION OF SOLIDS
(a) Define, for a wire,
(i) stress, [1]
(ii) strain. [1]
(b) A wire of length 1.70 m hangs vertically from a fixed point,...
Summer
3
Theory
CH20 - D.C. CIRCUITS
(a) A variable resistor is used to control the current in a circuit, as shown in Fig. 5.1. The variable resistor is connected in series with a 12V po...
Summer
1
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) State two assumptions of the simple kinetic model of a gas. [2]
(b) Use the kinetic model of gases and Newton's laws of motion to exp...
Summer
3
Theory
CH15 - SUPERPOSITION
(a) Explain the term interference. [1]
(b) A ripple tank is used to demonstrate interference between water waves.
Describe
(i) the appa...
Summer
2
Theory
CH1 - PHYSICAL QUANTITIES & UNITS
(a) Distinguish between scalar quantities and vector quantities. [2]
(b) In the following list, underline all the scalar quantities.
accelerati...
Summer
4
Theory
CH1 - PHYSICAL QUANTITIES & UNITS
(a) A sphere of radius $R$ is moving through a fluid with constant speed $v$. There is a frictional force $F$ acting on the sphere, which is given by ...
Summer
2
Theory
Potential Energy
(a) (i) Explain what is meant by work done. [1]
(ii) Define power. [1]
(b) Fig. 3.1 shows part of a fairground ride with a carriage on rai...
Summer
2