Q4:
AS & A Level Physics - 9702 Paper 2 2023 Summer Zone 1
Share
Previous
Questions:
4/8
Topic: CH5 - FORCES, DENSITY & PRESSURE
Solution
PRACTISE
Similar Questions
LEARN
Concepts with Sparky
More Questions from this Topic
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) Define density. [1]
(b) Figure 1 shows a cuboidal glass block.
A student measures the mass $m$ of the block and the side lengths $...
Winter
5
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) State what is meant by a vector quantity [2]
(b) A sphere falls vertically through a liquid that has density $830 \text{ kg m}^{-3}$. The sphere ...
Winter
5
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) Define density. [1]
(b) Figure 1 shows a cuboidal glass block.
A student measures the mass $m$ of the block and the side lengths $...
Winter
5
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) State what is meant by a vector quantity [2]
(b) A sphere falls vertically through a liquid that has density $830 \text{ kg m}^{-3}$. The sphere ...
Winter
5
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) State the principle of moments. [1]
(b) A rigid uniform beam rests on a pivot at its centre, as shown in Figure 1.
A load of...
Winter
7
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) State the principle of moments. [1]
(b) A rigid uniform beam rests on a pivot at its centre, as shown in Figure 1.
A load of...
Winter
7
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) The variation of stress with strain for a metal P is shown in Figure 1.
Point E is the elastic limit of the metal.
(i) Use Figure 1 to determi...
Winter
4
Theory
CH5 - FORCES, DENSITY & PRESSURE
(a) The variation of stress with strain for a metal P is shown in Figure 1.
Point E is the elastic limit of the metal.
(i) Use Figure 1 to determi...
Winter
4
MCQ
CH5 - FORCES, DENSITY & PRESSURE
Which single condition must apply for an object to be in equilibrium?
Winter
4
MCQ
CH5 - FORCES, DENSITY & PRESSURE
Which single condition must apply for an object to be in equilibrium?
Winter
4
More Questions from year 2023
MCQ
CH1 - PHYSICAL QUANTITIES & UNITS
Which unit is not an SI base unit?
Summer
3
MCQ
CH2 - MEASUREMENT TECHNIQUES
What is the best estimate of the number of atoms in a piece of metal of volume 50 cm$^3$?
Summer
3
MCQ
CH2 - MEASUREMENT TECHNIQUES
A copper pipe has a true diameter of 42.03 mm.A builder measures the diameter of the pipe five times using digital calipers. The measurements are show...
Summer
3
MCQ
CH3 - KINEMATICS
Two forces, each of 10 N, act at a point P, as shown. The angle between the directions of the forces is 120°. What is the magnitude of the result...
Summer
2
MCQ
CH3 - KINEMATICS
One object moves directly from P to R.
In a shorter time, a second object moves from P to Q to R.
Which statement about the two objects is correct...
Summer
3
MCQ
CH3 - KINEMATICS
A ball is kicked so that it has an initial velocity of 12 m s⁻¹ at an angle of 50° to horizontal ground.
Assume that air resistance is neg...
Summer
2
MCQ
CH4 - DYNAMICS
A camera drone of mass 1.20 kg hovers at a fixed point above the ground. The drone has four propellers.
In a time of 1.00 s, each propeller pushes ...
Summer
2
MCQ
CH4 - DYNAMICS
A box rests on the Earth, as shown.
Newton’s third law describes how forces of the same type act in pairs. One of the forces of a pair is the w...
Summer
3
MCQ
CH5 - FORCES, DENSITY & PRESSURE
A small ball is held at the surface of liquid oil in a container. The ball is released from rest and falls through the oil. The ball has velocity $v$....
Summer
3
MCQ
CH4 - DYNAMICS
An object of mass $m$, moving at speed $u$ along a frictionless horizontal surface, collides head-on with a stationary object of mass $4m$.
After t...
Summer
2