Internal resistance is a fundamental concept in electrical circuits, particularly in Direct Current (D.C.) systems. Understanding how internal resistance affects terminal potential difference is crucial for students pursuing AS & A Level Physics (9702) under the 'Practical Circuits' chapter of the D.C. Circuits unit. This knowledge not only aids in comprehending basic circuit behavior but also in designing and analyzing more complex electrical systems.

Key Concepts

The Basics of Internal Resistance

Internal resistance ($r$) refers to the opposition within a power source that limits the flow of electric current. Every real-world power source, such as batteries and generators, possesses some inherent internal resistance due to the materials and construction of the device. Unlike ideal voltage sources, which have zero internal resistance, real power sources experience a voltage drop when current flows through them.

Terminal Potential Difference

The terminal potential difference ($V$) is the voltage measured across the terminals of a power source when it is connected to an external circuit. It is given by the difference between the electromotive force (EMF) ($\mathcal{E}$) of the source and the voltage drop caused by the internal resistance. Mathematically, this relationship is expressed as:

$$V = \mathcal{E} - Ir$$

where $I$ is the current flowing through the circuit.

Electromotive Force (EMF)

Electromotive Force ($\mathcal{E}$) is the total energy provided by the power source per unit charge as it moves through the circuit. It represents the maximum potential difference of the source when no current is flowing (i.e., when the circuit is open). EMF is intrinsic to the power source and is independent of the current drawn by the external circuit.

Ohm’s Law and Internal Resistance

Ohm’s Law states that the current ($I$) flowing through a conductor between two points is directly proportional to the voltage ($V$) across the two points and inversely proportional to the resistance ($R$) of the conductor. When internal resistance is considered, Ohm's Law can be applied to the entire circuit as follows:

$$I = \frac{\mathcal{E}}{R + r}$$

Here, $R$ represents the external resistance, and $r$ is the internal resistance of the power source.

Impact of Internal Resistance on Terminal Voltage

The presence of internal resistance affects the terminal voltage of a power source when it is supplying current. As the current increases, the voltage drop across the internal resistance also increases, causing the terminal voltage to decrease. This phenomenon is particularly significant in high-current applications, where even small internal resistances can lead to substantial voltage drops.

For example, consider a battery with an EMF of 12 V and an internal resistance of 1 Ω connected to an external resistor of 3 Ω. The current flowing through the circuit can be calculated as:

$$I = \frac{12}{3 + 1} = 3 \text{ A}$$

The terminal voltage ($V$) is then:

$$V = 12 - (3 \times 1) = 9 \text{ V}$$

This demonstrates that the terminal voltage decreases as internal resistance and current increase.

Power Dissipation Due to Internal Resistance

Internal resistance not only affects terminal voltage but also leads to power dissipation within the power source itself. The power ($P$) dissipated can be calculated using:

$$P = I^2r$$

This power is lost as heat, reducing the overall efficiency of the power source.

Maximum Power Transfer Theorem

The Maximum Power Transfer Theorem states that maximum power is delivered to the external load when the external resistance ($R$) equals the internal resistance ($r$) of the power source. At this point, the terminal voltage drops to half of the EMF, and the power delivered to the load is maximized. The condition for maximum power transfer is:

$$R = r$$

Practical Implications in Circuit Design

Understanding the effects of internal resistance is vital in designing efficient circuits. Minimizing internal resistance in power sources leads to higher terminal voltages and improved efficiency. Conversely, in applications requiring controlled voltage drops, internal resistance can be advantageous. Engineers must balance these factors to optimize circuit performance based on specific requirements.

Advanced Concepts

Mathematical Derivation of Terminal Voltage

To delve deeper into the relationship between internal resistance and terminal voltage, consider the following derivation. Starting with the definition of EMF ($\mathcal{E}$) as the total energy per unit charge provided by the source:

$$\mathcal{E} = V + Ir$$

Rearranging the equation gives the terminal voltage:

$$V = \mathcal{E} - Ir$$

This equation quantifies how internal resistance causes a reduction in terminal voltage proportional to the current drawn from the source.

Advanced Problem-Solving: Variable Internal Resistance

Consider a scenario where a battery with an EMF of 9 V has an internal resistance that varies with temperature. Suppose the internal resistance doubles when the temperature increases by 30°C. If the initial internal resistance is 2 Ω and the external resistance is 4 Ω, calculate the terminal voltage before and after the temperature increase.

Initial internal resistance, $r_1 = 2 \text{ Ω}$
External resistance, $R = 4 \text{ Ω}$
EMF, $\mathcal{E} = 9 \text{ V}$

Initial current:

$$I_1 = \frac{9}{4 + 2} = 1.5 \text{ A}$$

Initial terminal voltage:

$$V_1 = 9 - (1.5 \times 2) = 6 \text{ V}$$

After temperature increase, internal resistance doubles:

$$r_2 = 2 \times 2 = 4 \text{ Ω}$$

New current:

$$I_2 = \frac{9}{4 + 4} = 1.125 \text{ A}$$

New terminal voltage:

$$V_2 = 9 - (1.125 \times 4) = 4.5 \text{ V}$$

This example illustrates how an increase in internal resistance leads to a decrease in terminal voltage.

Interdisciplinary Connections: Thermal Effects in Electrical Circuits

The relationship between internal resistance and terminal voltage extends beyond basic circuit theory into the realm of thermodynamics. As internal resistance leads to power dissipation ($P = I^2r$), heat is generated within the power source. This thermal effect can influence the performance and lifespan of electrical devices. Understanding this connection is essential in fields like electrical engineering and materials science, where managing heat is crucial for device reliability and efficiency.

Energy Efficiency and Internal Resistance

Energy efficiency in electrical systems is significantly impacted by internal resistance. High internal resistance results in greater energy loss as heat, reducing the overall efficiency of power transfer. In renewable energy systems, such as solar panels and wind turbines, minimizing internal resistance is vital for maximizing the conversion of natural energy sources into electrical energy. Strategies to enhance efficiency include using materials with lower resistivity and optimizing circuit designs to reduce resistive losses.

Internal Resistance in Electrochemical Cells

In electrochemical cells, internal resistance arises from ion transport and electrode reactions. Factors influencing internal resistance include electrode surface area, electrolyte concentration, and temperature. High internal resistance can impede the performance of batteries, limiting their discharge rates and reducing their capacity. Advances in battery technology aim to minimize internal resistance through the development of better materials and innovative cell designs.

Impact on Electronic Devices

Electronic devices rely on stable voltages for proper operation. Internal resistance plays a critical role in maintaining voltage regulation within devices. Variations in internal resistance can lead to fluctuations in terminal voltage, affecting the performance of sensitive components like microprocessors and sensors. Therefore, precise control of internal resistance is essential in designing reliable and high-performance electronic systems.

Mathematical Modeling of Internal Resistance

Advanced modeling techniques incorporate internal resistance into simulations of electrical circuits. Using differential equations and circuit theorems, engineers can predict how internal resistance affects transient and steady-state behaviors of circuits. For instance, in RC (resistor-capacitor) circuits, internal resistance influences the charging and discharging rates of capacitors, which is critical in signal processing and timing applications.

Optimization Techniques to Minimize Internal Resistance

Several optimization techniques are employed to minimize internal resistance in power sources:

Material Selection: Using materials with lower resistivity for electrodes and conductors reduces internal resistance.
Design Improvements: Increasing the surface area of electrodes enhances ion flow, thereby lowering resistance.
Temperature Management: Maintaining optimal temperatures can prevent resistance increases due to thermal effects.
Nanotechnology: Incorporating nanomaterials can significantly reduce internal resistance by providing more efficient pathways for charge carriers.

Implementing these techniques leads to more efficient and reliable power sources, essential for modern technological applications.

Comparison Table

Aspect	Ideal Voltage Source	Real Voltage Source
Internal Resistance ($r$)	0 Ω	Greater than 0 Ω
Terminal Voltage ($V$)	Equal to EMF ($\mathcal{E}$)	Less than EMF ($V = \mathcal{E} - Ir$)
Energy Efficiency	100%	Less than 100%
Heat Generation	None	Present ($P = I^2r$)
Performance Stability	Consistent	Depends on current and internal resistance

Summary and Key Takeaways

Internal resistance reduces the terminal voltage of a power source when current flows.
The relationship between EMF, terminal voltage, and internal resistance is fundamental in circuit analysis.
Higher internal resistance leads to greater power dissipation and lower energy efficiency.
Minimizing internal resistance is crucial for optimizing the performance of electrical devices and systems.
Understanding internal resistance is essential for effective circuit design and problem-solving in physics.

Examiner Tip

Tips

Remember the Formula: Always use $V = \mathcal{E} - Ir$ to differentiate between EMF and terminal voltage. This helps in accurately analyzing circuits with internal resistance. Visual Mnemonic: Think of internal resistance as a hurdle inside the battery that the current must overcome, reducing the voltage available to the external circuit. Practice Problems: Regularly solve problems involving internal resistance to reinforce your understanding and improve problem-solving speed for exams.

Did You Know

Did you know that the internal resistance of a battery can increase significantly as it ages? This phenomenon reduces the battery's efficiency and capacity, which is why older batteries often perform poorly. Additionally, internal resistance plays a critical role in electric vehicles, where minimizing it can lead to longer driving ranges and better performance.

Another interesting fact is that internal resistance is not only present in batteries but also in other power sources like fuel cells and solar panels. Engineers continuously work on reducing internal resistance in these technologies to enhance their efficiency and reliability in real-world applications.

Common Mistakes

1. Ignoring Internal Resistance: Students often assume ideal voltage sources with no internal resistance, leading to inaccurate calculations. Always account for internal resistance in real-world problems. Incorrect: Using $V = \mathcal{E}$ regardless of the circuit. Correct: Using $V = \mathcal{E} - Ir$ to find the terminal voltage.

2. Misapplying Ohm’s Law: Applying Ohm’s Law to the external resistor without considering the internal resistance can result in errors. Incorrect: $I = \frac{\mathcal{E}}{R}$ Correct: $I = \frac{\mathcal{E}}{R + r}$

3. Confusing EMF and Terminal Voltage: EMF is the total potential without current flow, while terminal voltage changes with current. Mixing these up can lead to misunderstanding circuit behavior. Incorrect: Treating EMF as the voltage across the terminals under load. Correct: Recognizing that terminal voltage decreases from EMF when current flows due to internal resistance.

FAQ

What is internal resistance?

Internal resistance is the inherent opposition within a power source that limits the flow of electric current. It causes a voltage drop when current flows through the source.

How does internal resistance affect terminal voltage?

Internal resistance causes the terminal voltage to decrease as the current increases. The relationship is given by $V = \mathcal{E} - Ir$, where $V$ is the terminal voltage.

Why is internal resistance important in circuit design?

Understanding internal resistance is crucial for designing efficient circuits, optimizing energy transfer, and ensuring the reliable performance of electrical devices.

What happens to power dissipation when internal resistance increases?

Power dissipation within the power source increases as internal resistance increases, following the formula $P = I^2r$. This leads to greater energy loss as heat.

Can internal resistance be zero?

In theoretical models, an ideal voltage source has zero internal resistance. However, in real-world power sources, some internal resistance is always present.

How can internal resistance be minimized?

Internal resistance can be minimized by using materials with lower resistivity, increasing the surface area of electrodes, optimizing design, managing temperature, and applying nanotechnology in power sources.

1. Capacitance

1.1 Energy Stored in a Capacitor

1.1.1 Determine electric potential energy stored in a capacitor from the area under the potential–charge g

1.1.2 Recall and use W = ½QV = ½CV²

1.2 Discharging a Capacitor

1.2.1 Analyze graphs of potential difference, charge, and current during capacitor discharge

1.2.2 Recall and use τ = RC for the time constant during discharge

1.2.3 Use equations of the form x = x₀e^(-t / RC) for current, charge, or potential during discharge

1.3 Capacitors and Capacitance

1.3.1 Define capacitance for isolated spherical conductors and parallel plate capacitors

1.3.2 Recall and use C = Q / V

1.3.3 Derive formulae for combined capacitance of capacitors in series and parallel

1.3.4 Use capacitance formulae for capacitors in series and parallel

2. Nuclear Physics

2.1 Mass Defect and Nuclear Binding Energy

2.1.1 Sketch the variation of binding energy per nucleon with nucleon number

2.1.2 Explain nuclear fusion and nuclear fission

2.1.3 Calculate the energy released in nuclear reactions using E = c²∆m

2.1.4 Understand the equivalence between energy and mass (E = mc²)

2.1.5 Define and use the terms mass defect and binding energy

2.2 Radioactive Decay

2.2.1 Understand that fluctuations in count rate provide evidence for random decay

2.2.2 Understand that radioactive decay is spontaneous and random

2.2.3 Define activity and decay constant, and recall A = λN

2.2.4 Define half-life

2.2.5 Use λ = 0.693 / t₁/₂ for the half-life relationship

2.2.6 Understand exponential decay and use the relationship x = x₀e^(-λt)

3. Kinematics

3.1 Equations of Motion

3.1.1 Define and use distance, displacement, speed, velocity, acceleration

3.1.2 Use graphical methods to represent motion

3.1.3 Determine displacement from velocity–time graph

3.1.4 Determine velocity using gradient of displacement–time graph

3.1.5 Determine acceleration using gradient of velocity–time graph

3.1.6 Derive equations for uniformly accelerated motion

3.1.7 Solve problems of uniformly accelerated motion

3.1.8 Describe experiment to determine acceleration due to gravity

3.1.9 Explain motion with uniform velocity and perpendicular acceleration

4. Deformation of Solids

4.1 Stress and Strain

4.1.1 Understand and use the terms load, extension, compression, and limit of proportionality

4.1.2 Recall and use Hooke’s law

4.1.3 Recall and use the formula for spring constant k = F / x

4.1.4 Define and use terms stress, strain, and Young's modulus

4.1.5 Describe an experiment to determine Young’s modulus

4.1.6 Understand deformation caused by tensile or compressive forces

4.2 Elastic and Plastic Behaviour

4.2.1 Understand elastic and plastic deformation and elastic limit

4.2.2 Understand area under the force–extension graph as work done

4.2.3 Calculate elastic potential energy using EP = ½kx²

5. Gravitational Fields

5.1 Gravitational Field of a Point Mass

5.1.1 Understand that g is approximately constant for small height changes near Earth's surface

5.1.2 Recall and use g = GM / r²

5.1.3 Derive and use g = GM / r² for gravitational field strength

5.2 Gravitational Potential

5.2.1 Define gravitational potential as work done per unit mass in bringing a test mass from infinity

5.2.2 Use ϕ = -GM / r for gravitational potential due to a point mass

5.2.3 Use EP = -GMm / r for gravitational potential energy between two point masses

5.3 Gravitational Field

5.3.1 Define gravitational field as force per unit mass

5.3.2 Represent a gravitational field using field lines

5.4 Gravitational Force Between Point Masses

5.4.1 For point outside uniform sphere, treat mass as a point mass at its center

5.4.2 Analyze circular orbits in gravitational fields

5.4.3 Recall and use Newton's law of gravitation F = Gm₁m₂ / r²

6. Electricity

6.1 Resistance and Resistivity

6.1.1 Understand that the resistance of a thermistor decreases as temperature increases

6.1.2 Define resistance and recall and use V = IR

6.1.3 Sketch I–V characteristics for metallic conductor, semiconductor diode, and filament lamp

6.1.4 Explain that the resistance of a filament lamp increases as current increases

6.1.5 State Ohm’s law and recall and use R = ρL / A

6.1.6 Understand that the resistance of an LDR decreases as light intensity increases

6.2 Electric Current

6.2.1 Understand that an electric current is a flow of charge carriers

6.2.2 Understand that the charge on charge carriers is quantised

6.2.3 Recall and use Q = It

6.2.4 Use I = Anvq for current-carrying conductors

6.3 Potential Difference and Power

6.3.1 Define potential difference as energy transferred per unit charge

6.3.2 Recall and use V = W / Q

6.3.3 Recall and use P = VI, P = I²R, P = V² / R

7. D.C. Circuits

7.1 Practical Circuits

7.1.1 Recall and use the circuit symbols in the syllabus

7.1.2 Draw and interpret circuit diagrams using circuit symbols

7.1.3 Define electromotive force (e.m.f.) of a source as energy transferred per unit charge

7.1.4 Distinguish between e.m.f. and potential difference (p.d.)

7.1.5 Understand the effects of internal resistance on terminal potential difference

7.2 Kirchhoff’s Laws

7.2.1 Recall Kirchhoff’s first law: conservation of charge

7.2.2 Recall Kirchhoff’s second law: conservation of energy

7.2.3 Derive the formula for combined resistance of resistors in series using Kirchhoff’s laws

7.2.4 Use the formula for combined resistance of resistors in series

7.2.5 Derive the formula for combined resistance of resistors in parallel using Kirchhoff’s laws

7.2.6 Use the formula for combined resistance of resistors in parallel

7.2.7 Use Kirchhoff’s laws to solve simple circuit problems

7.3 Potential Dividers

7.3.1 Understand the principle of a potential divider circuit

7.3.2 Recall and use the principle of the potentiometer for comparing potential differences

7.3.3 Understand the use of a galvanometer in null methods

7.3.4 Explain the use of thermistors and LDRs in potential dividers to provide a potential dependent on te

8. Thermal Equilibrium

8.1 Thermal Energy Transfer

8.1.1 Understand that thermal energy transfers from higher to lower temperature

8.1.2 Understand that regions of equal temperature are in thermal equilibrium

9. Temperature Scales

9.1 Temperature Measurement

9.1.1 Understand physical properties that vary with temperature (e.g., density, gas volume, resistance)

9.1.2 Convert temperatures between Kelvin and Celsius, and recall T(K) = θ(°C) + 273.15

10. Magnetic Fields

10.1 Concept of a Magnetic Field

10.1.1 Understand that a magnetic field is a field of force produced by moving charges or permanent magnets

10.1.2 Represent a magnetic field using field lines

10.2 Force on a Current-Carrying Conductor

10.2.1 Understand that a force acts on a current-carrying conductor in a magnetic field

10.2.2 Recall and use F = BIL sin θ for the force on a current-carrying conductor in a magnetic field

10.2.3 Define magnetic flux density as the force per unit current per unit length on a wire at right angles

10.3 Force on a Moving Charge

10.3.1 Determine the direction of the force on a charge moving in a magnetic field

10.3.2 Recall and use F = BQv sin θ for the force on a moving charge in a magnetic field

10.3.3 Understand the origin of the Hall voltage and use the expression VH = BI / (ntq) for the Hall voltag

10.3.4 Understand the use of a Hall probe to measure magnetic flux density

10.4 Magnetic Fields Due to Currents

10.4.1 Sketch magnetic field patterns due to currents in a straight wire, flat coil, and solenoid

10.4.2 Understand that magnetic field in a solenoid is increased by a ferrous core

10.4.3 Explain the origin of forces between current-carrying conductors and determine the direction of the

10.5 Electromagnetic Induction

10.5.1 Define magnetic flux as the product of magnetic flux density and area perpendicular to flux directio

10.5.2 Recall and use Φ = BA for magnetic flux

10.5.3 Understand and use the concept of magnetic flux linkage

10.5.4 Explain experiments that show changing magnetic flux induces an e.m.f.

10.5.5 Recall and use Faraday’s and Lenz’s laws of electromagnetic induction

11. Specific Heat Capacity and Latent Heat

11.1 Specific Heat Capacity

11.1.1 Define and use specific heat capacity

11.2 Latent Heat

11.2.1 Define and use specific latent heat; distinguish between fusion and vaporisation

12. Dynamics

12.1 Momentum and Newton’s Laws of Motion

12.1.1 Mass resists change in motion

12.1.2 Recall F = ma and solve related problems

12.1.3 Define and use linear momentum

12.1.4 Force as rate of change of momentum

12.1.5 State and apply Newton’s laws

12.1.6 Describe weight as effect of gravitational field

12.1.7 Weight of an object is mass × gravitational acceleration

12.2 Non-uniform Motion

12.2.1 Understand frictional and drag forces

12.2.2 Describe motion in uniform gravitational field with air resistance

12.2.3 Objects moving against resistive force may reach terminal velocity

12.3 Linear Momentum and its Conservation

12.3.1 State conservation of momentum

12.3.2 Apply conservation of momentum to solve problems

12.3.3 For elastic collision, kinetic energy and relative speed are conserved

12.3.4 Momentum is conserved, but some kinetic energy may change

13. Medical Physics

13.1 Production and Use of Ultrasound

13.1.1 Understand that a piezo-electric crystal changes shape when a p.d. is applied and generates an e.m.f

13.1.2 Understand how ultrasound waves are generated and detected by a piezoelectric transducer

13.1.3 Understand how ultrasound reflection at boundaries provides diagnostic information about internal st

13.1.4 Define specific acoustic impedance as Z = ρc

13.1.5 Use the equation IR / I₀ = (Z₁ – Z₂)² / (Z₁ + Z₂)² for the intensity reflection coefficient

13.2 Production and Use of X-rays

13.2.1 Explain that X-rays are produced by electron bombardment of a metal target and calculate the minimum

13.2.2 Understand the use of X-rays in imaging internal body structures and the term 'contrast' in X-ray im

13.2.3 Recall and use I = I₀e^(-μx) for the attenuation of X-rays in matter

13.2.4 Understand how computed tomography (CT) produces 3D images by combining multiple 2D X-ray images

13.3 PET Scanning

13.3.1 Understand that a tracer contains radioactive nuclei and is introduced into the body for imaging

13.3.2 Understand that β+ decay is used in positron emission tomography (PET)

13.3.3 Understand that annihilation occurs when a particle interacts with its antiparticle, conserving mass

13.3.4 Explain how gamma-ray photons from annihilation are detected to create an image of tracer concentrat

14. Waves

14.1 Progressive Waves

14.1.1 Describe wave motion in ropes, springs, and ripple tanks

14.1.2 Understand and use the terms displacement, amplitude, phase difference, period, frequency, wavelengt

14.1.3 Use time-base and y-gain on a cathode-ray oscilloscope (CRO) to determine frequency and amplitude

14.1.4 Derive and use v = f λ for the wave equation

14.1.5 Recall and use v = f λ

14.1.6 Understand energy transfer by a progressive wave

14.1.7 Recall and use intensity = power / area, intensity ∝ (amplitude)²

14.2 Transverse and Longitudinal Waves

14.2.1 Compare transverse and longitudinal waves

14.2.2 Analyze and interpret graphical representations of transverse and longitudinal waves

14.3 Doppler Effect for Sound Waves

14.3.1 Understand the change in frequency when a sound source moves relative to a stationary observer

14.3.2 Use the expression f₀ = fₛ(v / (v ± vₛ)) for the observed frequency

14.4 Electromagnetic Spectrum

14.4.1 State all electromagnetic waves are transverse waves traveling at the same speed in free space

14.4.2 Recall the range of wavelengths from radio waves to γ-rays

14.4.3 Recall that wavelengths 400–700 nm are visible to the human eye

14.5 Polarisation

14.5.1 Understand that polarisation is a phenomenon associated with transverse waves

14.5.2 Recall and use Malus's law (I = I₀ cos²θ) to calculate intensity of a plane-polarised wave after pas

15. The Mole

15.1 The Mole

15.1.1 Understand that amount of substance is an SI base quantity with the unit mol

15.1.2 Use molar quantities where one mole contains Avogadro's constant of particles

16. Equation of State

16.1 Ideal Gas Law

16.1.1 Understand that a gas obeying pV ∝ T is an ideal gas

16.1.2 Recall and use the equation pV = nRT for an ideal gas

16.1.3 Recall pV = NkT, where N = number of molecules and k is Boltzmann constant

16.1.4 Use the relationship k = R / NA

17. Kinetic Theory of Gases

17.1 Kinetic Theory

17.1.1 State the basic assumptions of the kinetic theory of gases

17.1.2 Explain pressure exerted by a gas due to molecular movement

17.1.3 Derive and use pV = (3/2)NmkT for pressure of a gas

17.1.4 Compare pV = (3/2)NmkT with pV = NkT to deduce average kinetic energy of a molecule

18. Particle Physics

18.1 Atoms, Nuclei and Radiation

18.1.1 Infer the existence and small size of the nucleus from α-particle scattering

18.1.2 Describe the nuclear atom model: protons, neutrons, and electrons

18.1.3 Distinguish between nucleon number and proton number

18.1.4 Understand isotopes as forms of the same element with different neutrons

18.1.5 Use the notation AZX for nuclides representation

18.1.6 Understand conservation of nucleon number and charge in nuclear processes

18.1.7 Describe the composition, mass, and charge of α-, β-, and γ-radiations

18.1.8 Understand antiparticles and positrons as antiparticles of electrons

18.1.9 State that (electron) antineutrinos are produced during β- decay and neutrinos during β+ decay

18.1.10 Represent α- and β-decay using radioactive decay equations

18.1.11 Use unified atomic mass unit (u) for mass

18.2 Fundamental Particles

18.2.1 Understand quarks as fundamental particles with six flavours

18.2.2 Understand hadrons as baryons (three quarks) or mesons (one quark and one antiquark)

18.2.3 Describe changes in quark composition during β- and β+ decay

18.2.4 Describe protons and neutrons as composed of quarks

18.2.5 Recall and use the charge of each quark and its respective antiquark

18.2.6 Recall electrons and neutrinos as fundamental particles (leptons)

19. Internal Energy

19.1 Internal Energy

19.1.1 Understand that internal energy is the sum of kinetic and potential energies of molecules in a syste

19.1.2 Relate rise in temperature to an increase in internal energy

20. Forces, Density and Pressure

20.1 Turning Effects of Forces

20.1.1 Weight acts at a single point: centre of gravity

20.1.2 Define and apply the moment of a force

20.1.3 Understand the concept of a couple

20.1.4 Define and apply torque of a couple

20.2 Equilibrium of Forces

20.2.1 State and apply the principle of moments

20.2.2 System in equilibrium has no resultant force or torque

20.2.3 Use a vector triangle to represent coplanar forces in equilibrium

20.3 Density and Pressure

20.3.1 Define and use density

20.3.2 Define and use pressure

20.3.3 Derive equation for hydrostatic pressure ∆p = ρg∆h

20.3.4 Use the equation ∆p = ρg∆h

20.3.5 Understand upthrust as the effect of hydrostatic pressure

20.3.6 Calculate upthrust using F = ρgV (Archimedes' principle)

21. Astronomy and Cosmology

21.1 Standard Candles

21.1.1 Understand luminosity as the total power radiated by a star

21.1.2 Recall and use the inverse square law F = L / (4πd²) for radiant flux intensity

21.1.3 Understand that an object with known luminosity is a standard candle

21.1.4 Use standard candles to determine distances to galaxies

21.2 Stellar Radii

21.2.1 Recall and use Wien’s displacement law λmax ∝ 1 / T to estimate the surface temperature of a star

21.2.2 Use Stefan–Boltzmann law L = 4πσr²T⁴

21.2.3 Use Wien’s law and Stefan–Boltzmann law to estimate the radius of a star

21.3 Hubble’s Law and Big Bang Theory

21.3.1 Understand redshift and the increase in wavelength of light from distant objects

21.3.2 Use ∆λ / λ = ∆f / f = v / c for redshift

21.3.3 Explain why redshift suggests the Universe is expanding

21.3.4 Recall and use Hubble’s law v = H₀d to explain the Big Bang theory

22. First Law of Thermodynamics

22.1 First Law

22.1.1 Recall and use W = p∆V for work done when the volume of a gas changes at constant pressure

22.1.2 Understand the difference between work done by a gas and work done on a gas

22.1.3 Recall and use the first law of thermodynamics: ∆U = q + W

23. Alternating Currents

23.1 Characteristics of Alternating Currents

23.1.1 Understand and use terms period, frequency, and peak value for alternating current or voltage

23.1.2 Use x = x₀ sin(ωt) for sinusoidal alternating current or voltage

23.1.3 Recall that the mean power in a resistive load is half the maximum power for sinusoidal current

23.1.4 Distinguish between root-mean-square (r.m.s.) and peak values and recall I₀r.m.s = I₀ / √2 and V₀r.m

23.2 Rectification and Smoothing

23.2.1 Distinguish graphically between half-wave and full-wave rectification

23.2.2 Explain the use of a single diode for half-wave rectification

23.2.3 Explain the use of four diodes (bridge rectifier) for full-wave rectification

23.2.4 Analyze the effect of a capacitor in smoothing, including the effect of capacitance and load resista

24. Superposition

24.1 Stationary Waves

24.1.1 Explain and use the principle of superposition

24.1.2 Understand experiments demonstrating stationary waves using microwaves, stretched strings, and air c

24.1.3 Explain the formation of stationary waves using graphical methods and identify nodes and antinodes

24.1.4 Determine wavelength from the positions of nodes or antinodes

24.2 Diffraction

24.2.1 Explain diffraction and show understanding of related experiments

24.2.2 Understand the effect of gap width relative to wavelength in diffraction experiments

24.3 Interference

24.3.1 Understand the terms interference and coherence

24.3.2 Demonstrate two-source interference using water waves, sound, light, and microwaves

24.3.3 Understand the conditions required for two-source interference fringes

24.3.4 Recall and use λ = ax / D for double-slit interference with light

24.4 Diffraction Grating

24.4.1 Recall and use d sin θ = nλ for diffraction grating calculations

24.4.2 Describe the use of a diffraction grating to determine the wavelength of light

25. Simple Harmonic Oscillations

25.1 Simple Harmonic Motion

25.1.1 Understand and use terms displacement, amplitude, period, frequency, angular frequency, and phase di

25.1.2 Understand that simple harmonic motion occurs when acceleration is proportional to displacement from

25.1.3 Use a = -ω²x and recall x = x₀ sin(ωt) as the solution

25.1.4 Use v = v₀ cos(ωt) and v = ±ω√(x₀² - x²) for velocity

26. Energy in Simple Harmonic Motion

26.1 Energy in SHM

26.1.1 Describe the interchange between kinetic and potential energy during SHM

26.1.2 Recall and use E = ½mω²x₀² for the total energy of a system undergoing SHM

27. Quantum Physics

27.1 Energy and Momentum of a Photon

27.1.1 Understand that electromagnetic radiation has a particulate nature

27.1.2 Recall and use E = hf for the energy of a photon

27.1.3 Use the electronvolt (eV) as a unit of energy

27.1.4 Understand that a photon has momentum and use p = E / c for photon momentum

27.2 Photoelectric Effect

27.2.1 Understand that photoelectrons are emitted from a metal surface when illuminated by electromagnetic

27.2.2 Understand and use the terms threshold frequency and threshold wavelength

27.2.3 Explain photoelectric emission in terms of photon energy and work function

27.2.4 Recall and use hf = Φ + ½mv² for the maximum kinetic energy of photoelectrons

27.2.5 Explain why the maximum kinetic energy of photoelectrons is independent of intensity, while current

27.3 Wave-Particle Duality

27.3.1 Understand that the photoelectric effect shows the particulate nature of light, while diffraction sh

27.3.2 Describe and interpret electron diffraction as evidence for the wave nature of particles

27.3.3 Understand the de Broglie wavelength as the wavelength associated with a moving particle

27.3.4 Recall and use λ = h / p for de Broglie wavelength

27.4 Energy Levels in Atoms and Line Spectra

27.4.1 Understand discrete electron energy levels in atoms (e.g., atomic hydrogen)

27.4.2 Understand the appearance and formation of emission and absorption line spectra

27.4.3 Recall and use hf = E₁ – E₂ for the energy difference between electron energy levels

28. Damped and Forced Oscillations, Resonance

28.1 Damped Oscillations

28.1.1 Understand that damping occurs due to resistive forces

28.1.2 Understand the types of damping: light, critical, and heavy damping

28.2 Resonance

28.2.1 Understand that resonance occurs when an oscillating system is forced to oscillate at its natural fr

29. Work, Energy and Power

29.1 Energy Conservation

29.1.1 Understand the concept of work, and recall W = F × s

29.1.2 Apply the principle of conservation of energy

29.1.3 Understand efficiency as useful energy output / total energy input

29.1.4 Use efficiency concept to solve problems

29.1.5 Define power as work done per unit time

29.1.6 Solve problems using P = W / t

29.1.7 Derive P = Fv and solve problems

29.2 Gravitational Potential Energy and Kinetic Energy

29.2.1 Derive ∆EP = mg∆h for gravitational potential energy changes

29.2.2 Recall and use ∆EP = mg∆h for gravitational potential energy changes

29.2.3 Derive EK = ½mv² for kinetic energy

29.2.4 Recall and use EK = ½mv² for kinetic energy

30. Electric Fields

30.1 Electric Fields and Field Lines

30.1.1 Understand that an electric field is a field of force and define it as force per unit positive charg

30.1.2 Represent an electric field using field lines

30.2 Uniform Electric Fields

30.2.1 Recall and use E = ∆V / ∆d to calculate electric field strength between charged parallel plates

30.2.2 Describe the effect of a uniform electric field on the motion of charged particles

30.3 Electric Force Between Point Charges

30.3.1 Understand that, for a point outside a spherical conductor, the charge may be considered a point mas

30.3.2 Recall and use Coulomb’s law F = Q₁Q₂ / (4πε₀r²) for the force between two point charges

30.4 Electric Field of a Point Charge

30.4.1 Recall and use E = Q / (4πε₀r²) for the electric field strength due to a point charge

30.5 Electric Potential

30.5.1 Define electric potential as work done per unit positive charge in bringing a test charge from infin

30.5.2 Recall and use V = Q / (4πε₀r) for electric potential due to a point charge

30.5.3 Understand how electric potential leads to electric potential energy of two point charges and use EP

31. Physical Quantities and Units

31.1 Physical Quantities

31.1.1 Physical quantities consist of magnitude and unit

31.1.2 Estimate physical quantities from the syllabus

31.2 SI Units

31.2.1 SI base units: mass, length, time, current, temperature

31.2.2 Express derived units from SI base units

31.2.3 Check homogeneity of physical equations

31.2.4 Use prefixes (pico, nano, micro, kilo, etc.)

31.3 Errors and Uncertainties

31.3.1 Understand systematic and random errors

31.3.2 Assess uncertainty in derived quantities

31.4 uniform Electric Fields

31.4.1 Distinguish between precision and accuracy

31.5 Scalars and Vectors

31.5.1 Difference between scalar and vector quantities

31.5.2 Add and subtract coplanar vectors

31.5.3 Represent a vector as components

32. Motion in a Circle

32.1 Centripetal Acceleration

32.1.1 Understand centripetal acceleration and its role in circular motion

32.1.2 Recall and use a = rω² and a = v² / r

32.1.3 Recall and use F = mrω² and F = mv² / r

32.1.4 Understand force causing centripetal acceleration is always perpendicular to motion

32.2 Kinematics of Uniform Circular Motion

32.2.1 Recall and use ω = 2π / T and v = rω

32.2.2 Understand and use angular speed

32.2.3 Define and express angular displacement in radians

Get PDF

PDF

Explore

Your Flashcards are Ready!

Understand the Effects of Internal Resistance on Terminal Potential Difference

Introduction